ITI Mechanic Motor Vehicle (MMV) 2nd Year CBT Exam Practice Paper 3

ITI Exam की बेहतर तैयारी के लिये मैकेनिक मोटर वाहन (एमएमवी) ट्रेड का ITI Mechanic Motor Vehicle (MMV) 2nd Year CBT Exam Practice Paper तैयार किया गया है जिसमे आपको 50 प्रश्‍न दिए जायेंगे और ITI Mechanic Motor Vehicle (MMV) 2nd Year CBT Exam Practice Paper New NIMI Pattern पर आधारित है। ITI Mechanic Motor Vehicle (MMV) 2nd Year CBT Exam Practice Paper मे जो प्रश्‍न दिये गये है वह हिंदी और अंग्रेजी दोनो भाषाओ में है।

ITI Mechanic Motor Vehicle (MMV) Trade के महत्वपूर्ण प्रश्नो का ITI Mechanic Motor Vehicle (MMV) 2nd Year CBT Exam Practice Paper देने के लिये नीचे दिये गये ITI Mechanic Motor Vehicle (MMV) 2nd Year CBT Exam Practice Paper पर क्लिक करें। उसके बाद Start Quiz पर क्लिक करें।

Start quiz

Q1. Which type of gear box provided with helical gears?

(A) Auto synchromesh gear box

(B) Constant mesh gear box

(C) Synchromesh gear box

(D) Sliding mesh gear box

Q2. What is the name of part marked as ‘X’ in the solenoid switch?

(A) Armature shaft

(B) Shift lever

(C) Fly wheel ring gear

(D) Pinion

Q3. What is the name of part marked as ‘X’ in the ignition coil?

(A) Primary winding

(B) Secondary winding

(C) Secondary cap

(D) Bakelite cap

Q4. What is the validity period for transport vehicle license?

(A) 10 Years

(B) 5 Years

(C) 8 Years

(D) 3 Years

Q5. What will be the result of defective clutch?

(A) Noise in gear shifting

(B) Gear slip

(C) Gear clash during shifting

(D) Gear locked in one gear

Q6. Which is the part of servo motor assembly?

(A) Gear reduction unit

(B) Normal AC motor

(C) Expansion valve

(D) MAP sensor

Q7. Why light weight cars use low steering ratio?

(A) To obtain low steering effect

(B) To obtain large steering effect

(C) To obtain no steering effect

(D) To obtain constant steering effect

Q8. What is the cause for alternator no charge when engine is running?

(A) Broken drive belt

(B) Brushes not seating properly

(C) Sticky regulator

(D)Low regulator setting

Q9. What causes high oil pressure?

(A) Water present in the oil

(B) Defective oil pump

(C) Defective relief valve

(D) Dirty oil filter

Q10. What is the name of part marked as ‘X’ in the horn circuit?

(A) Battery

(B) Solenoid switch

(C) Fuse

(D) Horn relay

Q11. Which factor affecting suspension?

(A) Damaged chassis frame

(B) Worn-out spring

(C) Abnormal tyre wear

(D) More shocks, uncomfortable riding

Q12. What will be the probable reason of low oil pressure?

(A) Worn out camshaft, crank shaft bearings

(B) Defective injector

(C) Carbon deposit on piston head

(D) More crankshaft end play

Q13. Which is noise free clutch?

(A) Single plate clutch

(B) Diaphragm spring type clutch

(C) Dog clutch

(D) Multi plate clutch

Q14. What is the type of horn?

(A) Air horn

(B) Wind horn

(C) Electric horn

(D) Bulb horn

Q15. What is the type of drive line?

(A) Front wheel drive line

(B) Center wheel drive line

(C) Rear wheel drive line

(D) Four wheel drive line

Q16. Which sensor causes off the outside air inlet or other odours?

(A) Infrared sensor

(B) Smog sensor

(C) Temperature sensor

(D) Sunload sensor

Q17. What is the expansion of GPS in vehicle safety system?

(A) Global Placing Systems

(B) Global Positioning Systems

(C) Global Preventing Systems

(D) General Positioning Systems

Q18. What is the name of device?

(A) Evaporator

(B) Blower

(C) Condenser

(D) Expansion valve

Q19. What is the name of component in the integral power steering system?

(A) Flow control valve

(B) Unloading valve

(C) Pressure release valve

(D) Rotary valve

Q20. What is the servicing procedure carried out in the wheel?

(A) Checking camber angle

(B) Checking kingpin inclination

(C) Checking castor angle

(D) Checking included angle

Q21. Where the starter motor located?

(A) Front side of engine

(B) Rear side of engine

(C) Bottom of engine

(D) Top side of engine

Q22. What is the name of part marked as ‘X’ in the rotor assembly?

(A) Field coil

(B) Laminated core

(C) Slip ring

(D) Connection to rectifier

Q23. What is the advantage of dual mass fly wheel?

(A) Prevent wrong clutch engagements

(B) Reduction of gear box and body noises

(C) Reduce the possibility of clutch slip

(D) Transmit the torque with less effort

Q24. Which system determine the vehicles location by forming a triangle with a group of four or more satellites?

(A) Triangulation

(B) Networking and Multiplexing

(C) Telematics

(D) Reflective displays

Q25. What is the type of constant velocity joint?

(A) Tripod joint

(B) Double joint

(C) Pot joint

(D) Ball joint

Q26. How many spark plugs are ignited at the same time in the distributor less ignition system?

(A) Two

(B) Four

(C) Three

(D) Five

Q27. Where the ambient temperature sensor is located in the vehicle?

(A) Behind the grill

(B) Rear side of engine

(C) Top of servo motor

(D) Front axle

Q28. What is the result of weak compression pressure?

(A) Low fuel consumption

(B) High oil consumption

(C) Lower power generation

(D) Engine will not start

Q29. How to rectify the defect of noise in hydraulic steering?

(A) Replace with new fluid

(B) Fill fluid to correct level and bleed the system

(C) Replace the flow control valve

(D) Adjust the torsion bar linkage

Q30. Which part of ignition system connects and disconnects primary circuit?

(A) Condenser

(B) Distributor

(C) Contact breaker

(D) Ignition coil

Q31. What is the name of shock absorber?

(A) Gas pressurised shock absorber

(B) Electronic adjustable shock absorber

(C) Load adjustable shock absorber

(D) Hydraulic shock absorber

Q32. What does the 3rd digit code no 9. indicate system trouble in scan tool letter codes?

(A) Ignition system

(B) Input/out signal and controls

(C) Computer system

(D) Emission system

Q33. Which type of gear converts rotary motion in to linear motion and vice versa?

(A) Helical gears

(B) Rack and Pinion

(C) Bevel gear

(D) Spur gear

Q34. What is the function of traction control system?

(A) Prevent wheel spinning

(B) Release the pressure to expansion tank

(C) Reduce steering effort

(D) Reduce the engine torque

Q35. What is the type of fixed constant velocity joint?

(A) Double joint

(B) Ball joint

(C) Tripod joint

(D) Pot joint

Q36. What is the type of joint?

(A) Ball and trunnion type universal joint

(B) Cross type universal joint

(C) Double joint

(D) Slip joint

Q37. What is the function of ambient temperature sensor in the air conditioning system?

(A) Monitor air temperature inside vehicle

(B) Monitor air temperature outside vehicle

(C) Monitor air temperature at the exhaust

(D) Monitor air temperature in driver cabin

Q38. What is the name of part marked as ‘X’ in the mechanical brake?

(A) Brake drum

(B) Brake shoe retracting spring

(C) Brake pedal

(D) Pedal return spring

Q39. What is the cause for low power generation?

(A) Improper tappet clearance

(B) High oil level

(C) Low oil viscosity

(D) Engine overheating

Q40. How the tyre height is calculated?

(A) Rim dia - tyre outer dia

(B) Tyre outer dia - Rim dia

(C) Tyre width + Bead circle dia

(D) Thread width + Tyre width

Q41. What is the name of part marked as ‘X’ in the single plate clutch?

(A) Gear box drive shaft

(B) Clutch plate hub

(C) Fly wheel

(D) Pressure plate

Q42. Which type of shock absorber maintain vehicle ride at a pre - set level according to the load placed over the rear axle?

(A) Gas pressurised shock absorber

(B) Mechanical shock absorber

(C) Automatic load adjustable shock absorber

(D) Hydraulic shock absorber

Q43. Which wire of servo motor connected to power supply?

(A) White

(B) Black

(C) Yellow

(D) Red

Q44. Which type of ECU control actuators of engine?

(A) VCM

(B) EBCM

(C) ECM

(D) TCM

Q45. What is the name of Horn?

(A) Bulb horn

(B) Air horn

(C) Electric horn

(D) Horn relay

Q46. What is the name of distance between most protruding portions on both sides of tyre?

(A) Tyre height

(B) Tyre outer diameter

(C) Tyre width

(D) Thread radius

Q47. What does the third digit of system trouble code no.6 deals with in scan tool letter code?

(A) Ignition system

(B) Transmission system

(C) Computer system

(D) Emission system

Q48. What is the purpose of indexing pin provided in the bulb case?

(A) Complete the circuit

(B) Retain the bulb in the socket

(C) For easy identification

(D) Prevent damage to light

Q49. How much is the current consumption of wind shield wiper motor?

(A) 2.7 to 3.4 Amps

(B) 2.2 to 3.2 Amps

(C) 3.5 to 5.2 Amps

(D) 1.8 to 3.2 Amps

Q50. What is the main feature of hydraulic actuated clutches?

(A) Pedal effort transmitted through spring

(B) Pedal effort transmitted through linkage

(C) Pedal effort transmitted through fluid

(D) Pedal effort transmitted through coupling

Mechanic Motor Vehicle 2nd Year cbt exam paper 3

You got {{userScore}} out of {{maxScore}} correct

{{title}}

{{image}}

{{content}}