ITI Mechanic Motor Vehicle (MMV) 1st Year CBT Exam Practice Paper 3

ITI Exam की बेहतर तैयारी के लिये मैकेनिक मोटर वाहन (एमएमवी) ट्रेड का ITI Mechanic Motor Vehicle (MMV) 1st Year CBT Exam Practice Paper तैयार किया गया है जिसमे आपको 50 प्रश्‍न दिए जायेंगे और ITI Mechanic Motor Vehicle (MMV) 1st Year CBT Exam Practice Paper New NIMI Pattern पर आधारित है। ITI Mechanic Motor Vehicle (MMV) 1st Year CBT Exam Practice Paper मे जो प्रश्‍न दिये गये है वह हिंदी और अंग्रेजी दोनो भाषाओ में है।

ITI Mechanic Motor Vehicle (MMV) Trade के महत्वपूर्ण प्रश्नो का ITI Mechanic Motor Vehicle (MMV) 1st Year CBT Exam Practice Paper देने के लिये नीचे दिये गये ITI Mechanic Motor Vehicle (MMV) 1st Year CBT Exam Practice Paper पर क्लिक करें। उसके बाद Start Quiz पर क्लिक करें।

Start quiz

Q1. Which drill machine is used to drill Multiple holes in one setting of work?

(A) Pillar drilling machine

(B) Hand drilling machine

(C) Column drilling machine

(D) Radial drilling machine

Q2. Which part is lubricated by splash lubrication system?

(A)Main journal

(B) Timing gears

(C) Crank pin

(D) Cylinder wall

Q3. Which device changes carbon monoxide into carbon dioxide in the exhaust gas?

(A) Muffler

(B) Canister

(C) Catalytic converter

(D) Exhaust gas regulator

Q4. What is the name of the safety sign?

(A) Wear head protection

(B) Protect head from rain

(C) Sun cap must be worn

(D) Only construction workers allowed

Q5. What is the working cycle of compression ignition engine?

(A) Diesel cycle

(B) Sterling cycle

(C) Otto cycle

(D) Rankin cycle

Q6. Which governor has fitted the control rack with diaphragm?

(A) Servo governor

(B) Pneumatic governor

(C) Mechanical governor

(D) Centrifugal governor

Q7. What is the material used to produce crank shaft?

(A) Chromium vanadium nickel steel

(B) High speed steel

(C)Wrought iron

(D) Cast iron

Q8. How does a turbocharger get drive?

(A) By gear

(B) By belt

(C) By inlet gas

(D) By exhaust gas

Q9. When do we use the hand priming pump?

(A) Engine is at rest

(B) Engine is at idling speed

(C) Engine is at full speed

(D) Engine is at full load

Q10. What is the purpose of the fly wheel timing mark?

(A) To coincide the gears

(B) To set the engine timing

(C) To set the valve clearance

(D) To set the F.I.P timing

Q11. Which device converts mechanical energy into pneumatic energy?

(A) Generator

(B) Actuator

(C) Alternator

(D) Compressor

Q12. Which device give high output at low speed?

(A) Dynamo

(B) Alternator

(C) Self motor

(D) Transformer

Q13. What is the major constituents of blow by gas?

(A) Hydro carbon

(B) CO₂

(C) Noᵪ

(D) CO

Q14. What is the property of a bearing helps to with stand metal to metal contact?

(A) Surface action

(B) Embeddability

(C) Fatigue strength

(D)Thermal conductivity

Q15. What is the purpose of throttle valve in the carburetor?

(A) Always holds correct fuel

(B) Filter the fuel

(C) Excess supply of fuel at idle

(D) Controls air fuel mixture into the engine

Q16. What is the name of part marked as ‘X’?

(A) Impeller

(B) Shaft

(C) Housing

(D) Pulley

Q17. How many flywheel rotation requires to complete one cycle in two stroke engine?

(A) One

(B) Two

(C) Four

(D) Three

Q18. How the amount of work done in a specification is called?

(A) Torque

(B) Power

(C) Stroke length

(D) X Stroke length

Q19. Which mixture is used in radiator reverse flushing cleaning?

(A) Flushing water with air (gun) pressure

(B) Flushing water with coolant oil

(C) Flushing water with engine oil

(D) Flushing water with soap oil

Q20. What is the name of indicator?

(A) Seat belt indicator

(B) Air bag indicator

(C) ABS indicator

(D) Brake indicator

Q21. Which tool used to tighten the nuts and bolts at recommended tightness?

(A) Pipe wrench

(B) Stud wrench

(C) Torque wrench

(D) Adjustable wrench

Q22. Which tool is used to make external thread on the pipe?

(A) Drill

(B) Tap

(C) Die

(D) Reamer

Q23. How much pressure develop the CRDI- diesel engine pump?

(A) 100 - 200 bar

(B) 600 - 1000 bar

(C) 200 - 600 bar

(D) 1000 - 1600 bar

Q24. What is the name of part marked as ‘x’?

(A) Spring

(B) Valve

(C) Cap assembly

(D) Valve seat

Q25. Which type of pump used in the hydraulic jack?

(A) Gear pump

(B) Plunger pump

(C) Internal gear pump

(D) Vane pump

Q26. Which is the bearing used in water pump?

(A) Ball bearing

(B) Taper roller bearing

(C) Needle bearing

(D) Roller bearing

Q27. Which valve is maintaining in the high pressure FIP pipe line?

(A) Control rack

(B) Delivery valve

(C) Plunger

(D) Barrel

Q28. Which tool is used to measure the diameter of the crank shaft main journal?

(A) Outside micrometer

(B) Inside micrometer

(C) Three point internal micrometer

(D) Master ring gauge

Q29. What is the process of driving exhaust gases in two stroke engine out of cylinder?

(A) Super charging

(B) Combustion

(C) Scavenging

(D) Intaking

Q30. Which process is taken place in catalytic converter?

(A) Physical

(B) Thermal

(C) Chemical

(D) Biological

Q31. What is the name of the indicator?

(A) Temperature warning

(B) Oil level / pressure warning

(C) Transmission warning

(D) Electrical system warning

Q32. Which instrument is used to check the vacuum of the cylinder?

(A) Dial gauge

(B) Compression gauge

(C) Vacuum gauge

(D) Wire gauge

Q33. Which acid is used in the lead acid Battery?

(A) Nitric acid

(B) Sulphuric acid

(C) Hydro chloric acid

(D) Hydro bromic acid

Q34. Which type of vehicle emissions is measured in “g/KWh”?

(A) Two wheeler and light motor vehicle

(B) Two wheeler

(C) Light motor vehicle

(D) Heavy motor vehicle

Q35. What is the name of the stroke?

(A) Suction stroke

(B) Exhaust stroke

(C) Power stroke

(D) Compression stroke

Q36. Name the drive on engine position.

(A) Rear engine - Rear wheel drive

(B) Front engine - Rear wheel drive

(C) Front engine - Four wheel drive

(D) Front engine - Front wheel drive

Q37. Which measuring gauge needs to be set up to a fixed dimension before use?

(A) Dial test indicator

(B) Depth gauge

(C) Dial bore gauge

(D) Vernier dial gauge

Q38. What is the name of the prohibition sign?

(A) Pedestrians prohibited

(B) One way prohibited

(C) Do not extinguish with water

(D) Smoking and naked flames prohibited

Q39. Which measuring instrument used to measure the Ampere, volt and resistance?

(A) Wattmeter

(B) Galvanometer

(C) Energy meter

(D) Multimeter

Q40. What is acronym for SCR in emission control system?

(A) Silicon Controlled Rectifier

(B) Selective Catalytic Reduction

(C) Selective Controlled Reduction

(D) Selective Controlled Rectifier

Q41. Which device converts hydraulic energy into mechanical energy?

(A) Actuator

(B) Control valve

(C) Compressor

(D) Regulator

Q42. What is the name of part marked as ‘x’?

(A) Oil filter bowl

(B) Air filter bowl

(C) Water filter bowl

(D) Fuel filter bowl

Q43. What is the name of the part marked as ‘X’?

(A) Face

(B) Crown

(C) Ring

(D) Skirt

Q44. What is the name of assembly marked as ‘x’?

(A) Hydraulic pump

(B) Water pump

(C) Fuel pump

(D) Oil pump

Q45. What is the name of the piston?

(A) Slipper piston

(B) Solid skirt piston

(C) Split skirt piston

(D) Piston with steel alloy inserts

Q46. What is the type of governor?

(A) Hydraulic governor

(B) Servo governor

(C) Pneumatic governor

(D) Mechanical governor

Q47. Which is the proposed date of implementation of Bharat stage - 5 in entire country?

(A) 1.4.2019

(B) 1.4.2018

(C) 1.4.2020

(D) 1.4.2025

Q48. What is the name of part marked as ‘X’?

(A) Bearing

(B) Impeller

(C) Oil seal

(D) Shaft

Q49. Which is the key element in converting reciprocating motion in to rotary motion?

(A) Connecting rod

(B) Cam shaft

(C) King pin

(D) Gudgeon pin

Q50. What is the name of part marked as ‘X’?

(A) Turbine wheel

(B) Turbine housing

(C) Compressor housing

(D) Compressor wheel

Mechanic Motor Vehicle 1st Year cbt exam paper 3

You got {{userScore}} out of {{maxScore}} correct

{{title}}

{{image}}

{{content}}