ITI Mechanic Motor Vehicle (MMV) 1st Year CBT Exam Practice Paper 2

ITI Exam की बेहतर तैयारी के लिये मैकेनिक मोटर वाहन (एमएमवी) ट्रेड का ITI Mechanic Motor Vehicle (MMV) 1st Year CBT Exam Practice Paper तैयार किया गया है जिसमे आपको 50 प्रश्‍न दिए जायेंगे और ITI Mechanic Motor Vehicle (MMV) 1st Year CBT Exam Practice Paper New NIMI Pattern पर आधारित है। ITI Mechanic Motor Vehicle (MMV) 1st Year CBT Exam Practice Paper मे जो प्रश्‍न दिये गये है वह हिंदी और अंग्रेजी दोनो भाषाओ में है।

ITI Mechanic Motor Vehicle (MMV) Trade के महत्वपूर्ण प्रश्नो का ITI Mechanic Motor Vehicle (MMV) 1st Year CBT Exam Practice Paper देने के लिये नीचे दिये गये ITI Mechanic Motor Vehicle (MMV) 1st Year CBT Exam Practice Paper पर क्लिक करें। उसके बाद Start Quiz पर क्लिक करें।

Start quiz

Q1. Which instrument used to check the piston ring end gap?

(A) Feeler gauge

(B) Vernier gauge

(C) Telescopic gauge

(D) Pitch gauge

Q2. Which part connect the piston with crank pin?

(A) Push rod

(B) Connecting rod

(C) Crank Shaft

(D) Cam Shaft

Q3. Where the carbon brushes are in contact with starting motor?

(A) Armature shaft

(B) Armature

(C) End cover

(D) Commutator

Q4. Which is the safety precaution to be adopted in handling diesel machine?

(A) Use correct viscosity oil

(B) Remove safeguard of rotating part

(C) Use diesel engine with loose mounting

(D) Use oil/greasy hand to repair work

Q5. What is the use of Ohmmeter in an electrical circuit?

(A) Measure the resistance

(B) Measure the power

(C) Measure the voltage

(D) Measure the current

Q6. What is the name of the cycle?

(A) Constant volume

(B) Constant pressure

(C) Isothermal

(D) Adiabatic

Q7. What is the stationary part of an alternator?

(A) Stator

(B) Rotor

(C) Pulley

(D) Slip rings

Q8. What is the use of hydrometer?

(A) To check specific gravity of electrolyte

(B) To check density of water

(C) To check density sulphuric acid

(D) To check temperature of electrolyte

Q9. What is the purpose of colour code in cables?

(A) Colour refers the voltage rating

(B) Colour refers the current rating

(C) Easy identification of each circuit

(D) Refers the size of the wire

Q10. What is the name of the portion below the piston boss?

(A) Ring section of the piston

(B) Land of the piston

(C) Crown of the piston

(D) Skirt of the piston

Q11. What is called the isolating the fire from the supply of oxygen by blanketing with foam and sand?

(A) Starting

(B) Cooling

(C) Misfiring

(D) Smothering

Q12. Where is the delivery pipe of fuel feed pump connected?

(A) Fuel tank

(B) Fuel filter

(C) Fuel injection pump

(D) Fuel gallery

Q13. What is the type of governor?

(A) Servo governor

(B) Pneumatic governor

(C) Hydraulic governor

(D) Mechanical governor

Q14. Which device give high output at low speed?

(A) Dynamo

(B) Alternator

(C) Self motor

(D) Transformer

Q15. What is the name of the component?

(A) Injector

(B) Feed pump

(C) Heater plug

(D) FIP

Q16. What is the name of the circuit?

(A) Open circuit

(B) Short circuit

(C) Parallel circuit

(D) Closed circuit

Q17. What is the type of the die?

(A) Die nut

(B) Rectangle split die

(C) Circular split die

(D) Half die

Q18. What is the name of the instrument?

(A) Ammeter

(B) Multimeter

(C) Voltmeter

(D) Hydrometer

Q19. What is the name of part marked as ‘X’?

(A) Shaft

(B) Bearing

(C) Oil seal

(D) Impeller

Q20. Which is the key element in converting reciprocating motion in to rotary motion?

(A) Connecting rod

(B) Gudgeon pin

(C)Cam shaft

(D) King pin

Q21. What is the name of the piston head?

(A) Flat head

(B) Domed head

(C) Irregular head

(D) Concave head

Q22. Name the drive on engine position.

(A) Front engine - Rear wheel drive

(B) Rear engine - Rear wheel drive

(C) Front engine - Front wheel drive

(D) Front engine - Four wheel drive

Q23. Which is used to convert AC to DC in alternator?

(A) Rotor

(B) Diodes

(C) Condenser

(D) Slip ring

Q24. How many crank shaft rotation required to open exhaust valve one time in four stoke engine?

(A) One

(B) Two

(C) Four

(D) Three

Q25.How much pressure develop the CRDI- diesel engine pump?

(A) 100 - 200 bar

(B) 600 - 1000 bar

(C) 200 - 600 bar

(D) 1000 - 1600 bar

Q26. Which type of vice is used to hold a job for drilling?

(A) Leg vice

(B) Bench vice

(C) Machine vice

(D) Hand vice

Q27. What is the name of the part marked as ‘X’?

(A) Valve door cover

(B) Cylinder head

(C) Oil pan

(D) Engine block

Q28. Which device used to step up the voltage in the spark ignition system?

(A) Ignition coil

(B) High Tension Cable

(C) Condenser

(D) Spark plug

Q29. Which device have the ability to store electrical charge?

(A) Capacitor

(B) Resistor

(C) Conductor

(D) Insulator

Q30. Which winding have thick wire in solenoid switch?

(A) Hold-in winding

(B) Field winding

(C) Armature winding

(D) Pull-in winding

Q31. Which automobile component produces dust?

(A) Piston

(B) Axle

(C) Gear box

(D) Brake shoe

Q32. What is the name of the part marked as‘X’?

(A) Skirt section

(B) Crown section

(C) Face section

(D) Ring section

Q33. What is the name of part marked as ‘x’?

(A) Reed valve

(B) By pass valve

(C) Pressure relief valve

(D) Inlet valve

Q34, What is the energy conversion of battery during discharge?

(A) Electrical energy into heat energy

(B) Chemical energy into electrical energy

(C) Electrical energy into mechanical energy

(D) Electrical energy into chemical energy

Q35. What is the name of the part marked as ‘X’?

(A) Crank pin

(B) Crank arm

(C) Main journal

(D) Balancing weight

Q36. Which is highly flammable liquid?

(A) LPG

(B) Water

(C) Crude oil

(D) Diesel

Q37. What is the name of part marked as ‘x’?

(A) Oil filter bowl

(B) Fuel filter bowl

(C) Air filter bowl

(D)Water filter bowl

Q38. What is the material of inlet manifold?

(A) Brass

(B) Stainless steel

(C) Bronze

(D) Aluminium alloy

Q39. Which instrument is used to measure the electrical resistance?

(A) Voltmeter

(B) Ammeter

(C) Ohmmeter

(D) Wattmeter

Q40. Which angle of drill bit prevents the friction behind the cutting edge?

(A) Rake angle

(B) Point angle

(C) Clearance angle

(D) Helix angle

Q41. What is ovality of a crank shaft?

(A) Difference in dia measured from top to bottom of a crank shaft outer dia

(B) Difference in dia measured thrust to non thrust across dia

(C) Difference in dia measured only at bottom

(D) Difference in dia measured only at top

Q42. Which metal in the fuel is to be avoided while fitting catalytic converter?

(A) Tin

(B) Lead

(C) Phosphorus

(D) Chromium

Q43. What is the purpose of the fly wheel timing mark?

(A) To coincide the gears

(B) To set the engine timing

(C) To set the valve clearance

(D) To set the F.I.P timing

Q44. How many cells are in the 12V Battery?

(A) 2 cells

(B) 6 cells

(C) 12 cells

(D) 9 cells

Q45. Which system the gear type oil pump is used?

(A) Lubrication system

(B) Cooling system

(C) Fuel system

(D) Air conditioning system

Q46. Which part connect the piston with connecting rod?

(A) Piston pin

(B) Crank pin

(C) Spilt pin

(D) Cotter pin

Q47. What is the effect if thermostat valve is struck?

(A) Engine gets over cooling

(B) Engine gets over heating

(C) Engine does not stop

(D) Engine does not start

Q48. What is the name of part marked as ‘x’?

(A)Cheek

(B) Face

(C) Wedge

(D) Pein

Q49. Which types of safety involves wearing of safety shoes and goggle in a workshop?

(A) General safety

(B) Personal safety

(C) General and machine safety

(D) Machine safety

Q50. Which part allows to flow water from upper tank to lower tank of the radiator?

(A) Fins

(B) Core tubes

(C) Bottom hole

(D) Water pump

Mechanic Motor Vehicle 1st Year cbt exam paper 2

You got {{userScore}} out of {{maxScore}} correct

{{title}}

{{image}}

{{content}}