ITI Plumber 1st Year CBT Exam Practice Paper 5

December 16, 2024 ITI Exam

ITI Exam की बेहतर तैयारी के लिये प्लंबर ट्रेड का ITI Plumber 1st Year CBT Exam Practice Paper तैयार किया गया है जिसमे आपको 50 प्रश्‍न दिए जायेंगे और ITI Plumber 1st Year CBT Exam Practice Paper New NIMI Pattern पर आधारित है। ITI Plumber 1st Year CBT Exam Practice Paper मे जो प्रश्‍न दिये गये है वह हिंदी और अंग्रेजी दोनो भाषाओ में है।

ITI Plumber Trade के महत्वपूर्ण प्रश्नो का ITI Plumber 1st Year CBT Exam Practice Paper देने के लिये नीचे दिये गये ITI Plumber 1st Year CBT Exam Practice Paper पर क्लिक करें। उसके बाद Start Quiz पर क्लिक करें।

Q1. Which material is used to manufacture punch?

(A) Low carbon steel

(B) High carbon steel

(D) Medium carbon steel

Q2.What is the type of water tank?

(A) Over head tank

(B) Sump

(D) Rotational moulded polyethylene storage tank

Q3. Why dry sand is filled before bending the pipe by hot bending method?

(A) Preventing the tube from cracking

(B) Preventing the tube from lengthening

(D) To avoid colour change

Q4. What is the name of caliper?

(A) Divider

(B) Odd leg caliper

(D) Outside caliper

Q5. What is the use of union in a pipe line?

(A) Easy to pump

(B) Easy to dismantle

(D) Easy to flow water

Q6. What is the standard height from floor to the top of the sink?

(A) 90cm

(B) 105cm

(D) 95cm

Q7. What is the cause of permanent hardness in the water?

(A) Garbage

(B) Clay, silt

(D) Bicarbonates of calcium

Q8. What is the purpose of an inspection chamber in a house drainage system?

(A) Maintenance

(B) Fire fighting

(D) Pumping

Q9. Which is the process of water softening treatment works based on ion-exchange process?

(A) Reverse osmosis process

(B) Lime soda process

(D) Demineralization process

Q10. Which water supply distribution system is for town growing irregularly?

(A) Tree system

(B) Ring system

(D) Radial system

Q11. What is the name of part marked as ‘X’?

(A) Block

(B) Flaring

(D) Flaring bar

Q12. What is the reason for damaged spindle in bench vice?

(A) Wrong handling of spindle

(B) Over tightening the vice

(D) Bent on spindle lever

Q13. Which valve is used for removing mud and sludge from the reservoir?

(A) Scour valve

(B) Mud valve

(D) Sluice valve

Q14. What is the cause for leakage in pipe line?

(A) Metering supply system

(B) Intermittent supply system

(D) Bad joints and connection

Q15. What is the name of valve?

(A) Air relief valve

(B) Plug valve

(D) Pressure relief valve

Q16. What is the advantage of cast iron pipes?

(A) Less corrosion

(B) Rarely available

(D) Costly

Q17. What is the name of part marked as ‘X’ in hand vice?

(A) Spring

(B)Temper plate

(D) Wing nut

Q18. What is the maximum diameter that can be bent in radius collar unit?

(A) 20mm

(B) 65mm

(D) 75mm

Q19. Which test is to find the hardness of water?

(A) Physical test

(B) Chemical test

(D) Bacteriological test

Q20. What is the name of tool?

(A) Valve spindle

(B) Reseating tool

(D) Hand grinder

Q21. What is the pressure maintained in the pipe lines at fire hydrants position if pumped through motor?

(A) 35 to 50 meters head

(B) 7 to 14 meters head

(D) 15 to 30 meters head

Q22. What is filling in pipe bending?

(A) Cool the pipes after bending

(B) Dry fine silican sand

(D) Hold the pipes in template

Q23. What are the metallic elements of solder?

(A) Lead and Tin

(B) Lead and Copper

(D)Lead and Zinc

Q24. What is the other name of floor trap?

(A) Bottle trap

(B) Nahani trap

(C ) Gully trap

(D) Intercepting trap

Q25. What is the maximum suction limit for a hand pump?

(A) 10 meter

(B) 8 meter

(D) 4 meter

Q26. What is the minimum standard size of gully trap?

(A) 100 x 100

(B) 200 x 90

(D) 100 x 80

Q27. What is the name of symbol?

(A) Turning down/away

(B) Turning up/towards

(D) Side outlet (outlet down)

Q28. What is the part marked as ‘X’?

(A) Yoke

(B) Clamp

(D) Movable collar

Q29. Which type of joints are used for the pipes subjected to severe changes in temperature?

(A) Flanged joints

(B) Expansion joints

(D) Screwed joints

Q30. Which personal protective equipment (PPE) is used for head protection?

(A) Gum boots

(B) Helmet

(D) Nose mask

Q31. Which precaution is to be observed while cutting threads in G.I pipe?

(A) Clean the thread with a wire brush

(B) Apply little pressure to the die stock

(D) Apply a soluble oil

Q32. How much is distance between fire hydrants provided along the roads?

(A) 50 to 100 meters

(B) 100 to 130 meters

(D) 150 to 200 meters

Q33. What for chilling carried after bending in pipe?

(A) Cool the pipe after hot bending

(B) Hold the pipes in bending machine

(D) Empty the pipe after hot bending

Q34. What is the name of sanitary fitting?

(A) Hand dryer

(B) Corner urinal

(D) Automatic soap dispenser

Q35.What is the pressure range between the dissolved acetylene gas cylinder?

(A) 120 to 150 Kg/cm²

(B) 15 to 16 Kg/cm²

(D) 110 to 120 Kg/cm²

Q36. What is the purpose of using hemp packing in the pipe thread?

(A) To provide cushioning effect

(B) To prevent leakage

(D) To prevent damage to thread

Q37. What is the alloy of soft solder?

(A) Lead and bronze

(B) Lead and copper

(D) Lead and tin

Q38, What is the equipment used for masonry work?

(A) Wooden peg

(B) Mason’s square

(D) Mason trowel

Q39. Which system is used for distribution of water pumped directly to achieve the required pressure?

(A) Gravity system

(B) Pumping system

(D) Dual system

Q40. What is the disadvantage of a centrifugal pump?

(A) Electrical driven

(B) Need priming

(D) Easy to repair

Q41. What is the maximum compressive strength of third class bricks?

(A) 35 Kg/cm²

(B)45 Kg/cm²

(D) 50 Kg/cm²

Q42. What is the name of joint that has threads on both sides of the central piece?

(A) Barrel nipple

(B) Double nipple

(D) Reducer

Q43. Which fitting is used to connect one length to another for continuation of the pipe?

(A) Tee

(B) Reducer

(D) Socket

Q44. What is the advantage of air testing?

(A) Low expense

(B) Repairing easy

(D) Equal pressure distributes in all

Q45. What is the name of part marked as ‘X’ in hydraulic bending machine?

(A) Back former

(B) Inner former

(D) Hydraulic ram

Q46. Which valve is used in high pressure applications?

(A) Globe valve

(B) Sluice valve

(D) Float valve

Q47. What is the name of part marked as ‘X’?

(A) Degrees of bend

(B) Gain scale

(D) Bending tool

Q48. What is the advantage of universal surface gauge?

(A) Light in weight

(B)Mark parallel lines on both inside and outside edges

(D) Fine adjustment made quickly

Q49.Which marking media is available in different colours?

(A) Copper sulphate

(B) Prussian blue

(D) Whitewash

Q50. What is the colour code for plastic waste bin?

(A) Red

(B) Green

(D) Yellow

Plumber 1st Year cbt exam paper 5

You got {{userScore}} out of {{maxScore}} correct

Youtube Click here

Telegram Group Join Now

Whatsapp Group Join Now

Facebook Group Join Now

Instagram Follow

Application Download Now

Leave a Reply Cancel reply